The aluminum 600-volt USE cable is made for use in secondary circuit distributions, duct installation, and direct burial uses. The highest working temperature is 90 degrees in dry and wet locations. voltage rating is about six hundred volts. The ampacity char is a method to find ampers of aluminum wires. So let’s get started with What is 4.0 aluminum wire rated for?
Aluminum Wire Ampacity Chart
Amapcity wire is used for finding the value of ampers used by aluminum wire. Here is a table made to show the value of the ampacity of aluminum wire.
| Aluminum AWG size | Ampacity at (60 C) | Ampacity at (75 degrees Celsius) | Ampacity at (90 C) |
Maximum amps (75C)
|
| 0000 (4/0) AWG | 150 Amps | 180 Amps | 205 Amps |
144 Amps
|
| 000 (3/0) AWG | 130 Amps | 155 Amps | 175 Amps |
124 Amps
|
| 00 (2/0) AWG | 115 Amps | 135 Amps | 150 Amps |
108 Amps
|
| 0 (1/0) AWG | 100 Amps | 120 Amps | 135 Amps |
96 Amps
|
| 1 AWG | 85 Amps | 100 Amps | 115 Amps |
80 Amps
|
| 2 AWG | 75 Amps | 90 Amps | 100 Amps |
72 Amps
|
| 3 AWG | 65 Amps | 75 Amps | 85 Amps |
60 Amps
|
| 4 AWG | 55 Amps | 65 Amps | 75 Amps |
52 Amps
|
| 6 AWG | 40 Amps | 50 Amps | 60 Amps |
40 Amps
|
| 8 AWG | 30 Amps | 40 Amps | 45 Amps |
32 Amps
|
| 10 AWG | 25 Amps | 30 Amps | 35 Amps |
24 Amps
|
| 12 AWG | 20 Amps | 20 Amps | 25 Amps |
16 Amps
|
What is Wire Size & Amp Ratings
- The ampacity is the highest curent the conductor can handle without affecting the temperature rating. The current measuring unit is ampere. use the accurate size of the wire for the current needed for the circuit to avoid the wire from overheating.
- The number and type of devices attached to the circuit define the ampacity needed by the conductor. Normally circuit used in huses is made for twenty ampers. A lighting circuit can be made for 15 ampers.
- For measuring the load needed for the circuit first of all add the watts of all devices connected with the circuit. After that divide the total watt by the voltage of the system normally 120 or 240 and provide the current or ampers needed
How many amps can a 4 0 aluminum wire carry?
- The 4/0 aluminum THHN, THW, or XHHW is used for 200 service entray but it is rated for 180 ampers. Conductor ampacity is limited through insulation as to how much it gets heated before damaging.
What is 4 0 aluminum wire used for?
- The 4/0 aluminum XHHW/ XHHW-2Â wires are normally used to distribute power and are also known as feeders. They can be connected in conditions that are dry or wet so their temperature must not be higher than 90 degrees and used in conduit.
What is number 4 aluminum good for?
- XHHW-2 is used in air ducts, conduits, or raceways for services, feeder, and branch circuit wiring.
How many amps is 4 gauge wire rated for?
| 10 AWG – 30 AMPS | 4 AWG –Â 85 AMPS |
Is 4 0 aluminum wire good for 200 amp service?
- For installing the 200 amp service there is a need of about 3/0 AWG copper wire or 4/0 AWG aluminum. The ampacity of 3/0 copper wire is about 225 ampers and the ampacity of 4/0 aluminum wire is 205Â Amp.
What is the load capacity of 4mm wire?
- 5000 watts load.
Can 4 wire carry 100 amps?
- There is a need to use #4 AWG wire if the distance between the panel and the utility is less than fifty feet.
Is 4 gauge wire good for a 2000-watt amp?
- For the audio power ampere and supposing an 8-ohm speaker, take the square root of 2000W divided by 8 ohms is 15.81 ampere. So there is a need for 10Â to 12AWG.
What is 4 0 wire size?
| Gauge No. | Inches | Millimeters |
|---|---|---|
| 4/0 | 0.460000 | 11.68 |
What gauge is 4 0 cable?
| American Wire Gauge (AWG) | Diameter (in) | Cross-sectional area (mm2) |
|---|---|---|
| 0000 (4/0) | 0.460 | 107.0 |
Is #4 aluminum good for 60 amps?
- The 4 aluminum is best for 65 amperes at 130″\’ voltage loss at sixty amperes will be 2.55%.
What size aluminum is good for 50 amps?
- Based on the permitted ampacity of aluminum and copper wire use 6AWG copper wire and 4 AWG aluminum wire for 50 amp circuit breaker. it is recommended for cable running for 100 feet or less.
What is the load capacity of 4mm Aluminium wire?
16 Ampere (Amp)
What is the difference between 2 0 and 4 0 aluminum wire?
The 2/0 copper service entrance code cable is best for 200 amps and needs 4/0 aluminum much thicker cable to carry for similar load. The difference in size is less for sixty amperes but can be complex for high installations.
What is 4 0 4 0 2 0 aluminum wire used for?
4/0-4/0-2/0 aluminum URD is employed for the connection of the transformer with a meter base and is best for direct burial.
How many wires are in a 4-0 aluminum wire?
| Cable Type | XHHW-2 |
|---|---|
| # of Conductors | 1 Conductor |
| O.D. (Inches) | 0.585 |
| Ampacity | 205 |
| Voltage | 600V |
Read Also;
- Two Way Switching Explained – How to wire 2 way light switch
- 30 Amp Wire Size: What AWG Wire You Need?
- 125 Amp Wire Size and Breaker Guide
- 60 Amp Wire Size – Which AWG is Best for 60 Amp Breaker
- What Size Wire for 100 Amp Service
- What Size Wire Do I Need for a 60 Amp Sub Panel?
- What Gauge Wire for 30 AMP 220v
